CHIMCHAR (Happy New Year!)

390 / CHIMCHAR - Pokémon Papercraft
Name: Chimchar
Type: Fire
Species: Chimp Pokémon
Height: 0.5 m (1'08")
Weight: 6.2 kg (13.7 lbs.)
Interesting Facts: Chimchar is a bipedal Pokémon resembling a chimpanzee. It's body is mainly a shade of orange, but some parts such as face, belly, hands are light yellow. The flames on it's rear are produced by gas burning in it's stomach. These flames go out when it sleeps. It's very agile, being able to climb the ledges of tall mountains, the place where it lives.

THE PAPER MODEL
Height: 21.2 cm / 8.3 in
Width: 9.3 cm / 3.7 in
Depth: 16.7 cm / 6.6 in
Pages: 4
Pieces: 43
Level: Medium-Hard(no flames)/Hard(flames)
Designer: Brandon
Photo: LuIS
NOTES: Start it at the bottom of the head and close at the top. Same with the body, start at the legs and close at the neck. The fingers can be tricky, so take your time with them. The tail is the hardest part, and it's also optional. So in case you want to build it, be careful, fold the lines and take your time. Also, make sure to glue it before going far with the body. It takes some weight to stand so, before closing the body, add some weight by the unglued tabs of the last piece and place the head til it stands. After you have found the balance and the model stands, close the body and glue the head, but not with a lot of glue.

Download: A4 / Letter

AZUMARILL (MERRY CHRISTMAS!)

184 / AZUMARILL - Pokémon Papercraft
Name: Azumarill
Type: Water/Fairy
Species:  Aqua Rabbit Pokémon
Height: 0.8 m (2'07")
Weight: 28.5 kg (62.8 lbs.)
Interesting Facts: Azumarill has highly developed hearing that allows it to hear distances, even when it is underwater. By keeping still and listening closely, it can tell what is in even wild, fast-moving rivers. Azumarill can make balloons out of air. It makes these air balloons if it spots a drowning Pokémon. It lives in rivers and lakes, and can live in the water all day long.

THE PAPER MODEL
Height: 17.0 cm/6.7 in
Width: 16.9 cm/6.7 in
Depth: 11.8 cm/4.6 in
No. of Pages: 4
No. of Pieces: 38
Level: Easy-Medium
Designer: Brandon
Photo: LuIS

NOTES: Start at the ears and build to the bottom, joining the arms as you go. Close at the indicated place. The feet close at the bottom, glue them to to body as soon as they are done. If connected correctly, it won't need weight to stand. Glue the tail after, but only the first part, gluing the ball is the last thing you'll do. Fez and bowtie are optional.

Download: A4 / Letter

DEDENNE

702 / DEDENNE - Pokémon Papercraft

Name: Dedenne
Type: Electric/Fairy
Species: Antenna Pokémon
Height: 0.2 m (0′08″)
Weight: 2.2 kg (4.9 lbs.)
Interesting Facts: Dedenne is a round, small, orange mouse-like Pokémon, whose whiskers are in shape of antennas, which it uses to communicate with far-off allies. It has orange pouches on its cheeks that charge electricity, and its belly is a pale yellow. It has round black ears with light yellow insides, and a long black tail with a star-like tip. It has an aradicular tooth that can be seen on its upper jaw. Its tail can absorb electricity from power plants or house outlets. It can then fire electricity from its whiskers.

THE PAPER MODEL
Height: 13.6 cm/ 5.4 in
Width: 15.3 cm/ 6 in
Depth: 13.9 cm/ 5.5 in
Pages: 4
Pieces: 40
Level: Medium
Designer: PODragon
Photo: LuIS
NOTES: Start at the head, joining the ears as you go. The whiskers you can either glue them now or at the end. Start the arms at the hands, folding the hands. Close the model at the bottom, where the feet will glue, but before glue the tail and put some weight inside, so it stands. If not for the tip of the tail this model would be an easy one, so fold both the pieces, refer to the pdo and take your time there. The scarf is optional and comes with 2 different textures. Instructions on how to build it included on the template. It won't go through the head, so you'll have to glue the tab of the bigger piece while placing it on the body.

Download: A4 / Letter

MEGA LATIOS

381 / M Latios - Pokémon Papercraft
Name: M Latios
Type: Dragon/Psychic
Species:  Eon Pokémon
Height: 2.3 m (7'07")
Weight: 70.0 kg (154.3 lbs.)
Interesting Facts: Latios made its debut appearance in Pokémon Heroes. Annie and Oakley captured Latios and used it to power the Defense Mechanism of Alto Mare along with the stolen Soul Dew. Latios ended up sacrificing itself to save Alto Mare from an enormous tidal wave.

THE PAPER MODEL
Height: 16.0 cm/6.3 in
Width: 44.8 cm/17.6 in
Depth: 28.9 cm/11.4 in
No. of Pages: 10 (Including Base)
No. of Pieces: 71
Level: Medium
Designer: Brandon
Photo: LuIS

NOTES: Start at the head and build by numbers until you get to the tail, glue the arms (using the base as a tool to glue them on the right position) and only after close. It's important to note that the arms are very heavy and the tube that holds them to the body is very small, so it may collapse if not reinforced with a tube of rolled paper inserted inside. The is not as hard as it seems, take your time, join one at a time to the hand and you'll be fine. The medium-hard for Mega Latias is due to the hands, the pieces get small, and a bit harder to build, but besides that shouldn't be too hard. Further instructions included on the template.

Base, Soul Dew, and Mega Stones included, as well as eye textures for Latias. The only difference for Latias is eye, and size.

Download: A4 / Letter

MEGA LATIAS

380 / M Latias - Pokémon Papercraft
Name: M Latias
Type: Dragon/Psychic
Species:  Eon Pokémon
Height: 1.8 m (5'11")
Weight: 52.0 kg (114.6 lbs.)
Interesting Facts: A Latias also appeared in Pikachu's Ocean Adventure where, along with Latios, it used its powers to help Pikachu, Meowth, and the other Pokémon search for the legendary "Wailord's Tear" beneath the ocean. A Latias appeared in SS025 under the ownership of Nurse Joy. It was used against Forrest's Rhyperior in a battle to prove Forrest's capabilities as a potential Gym Leader, where Latias proved victorious.

THE PAPER MODEL
Height: 12.5 cm/4.9 in
Width: 35.0 cm/13.8 in
Depth: 22.6 cm/8.9 in
No. of Pages: 6 (Including Base)
No. of Pieces: 71
Level: Medium-Hard
Designer: Brandon
Photo: LuIS

NOTES: Start at the head and build by numbers until you get to the tail, glue the arms (using the base as a tool to glue them on the right position) and only after close. It's important to note that the arms are very heavy and the tube that holds them to the body is very small, so it may collapse if not reinforced with a tube of rolled paper inserted inside. The is not as hard as it seems, take your time, join one at a time to the hand and you'll be fine. The medium-hard for Mega Latias is due to the hands, the pieces get small, and a bit harder to build, but besides that shouldn't be too hard. Further instructions included on the template.

Base, Soul Dew, and Mega Stones included, as well as eye textures for Latias. The only difference for Latias is eye, and size.

Download: A4 / Letter

LUXIO

404 / LUXIO - Pokémon Papercraft

Name: Luxio
Type: Electric
Species: Spark Pokémon
Height: 0.9 m (2′11″)
Weight: 30.5 kg (67.2 lbs.)
Interesting Facts: Luxio is a feline, quadruped Pokémon resembling a young lynx or lion. Blue and black fur covers most of its body. Its ears, face, hind paws, and front half of its body are blue, while its hindquarters are black. Additionally, Luxio has a tufty black mane surrounding its face. The mane is longer on the male Luxio, while the fur on the hind paws extends to ankles on the female. The insides of its rounded are yellow, as are its eyes. There are two yellow rings around each front leg and a yellow, four-point star on the tip of its tail. Luxio is able to communicate with others of its kind using electrical pulses from its claws. Luxio lives in small groups, and is able to generate powerful electricity by gathering the group's tails together.

THE PAPER MODEL
Height: 18.0 cm/ 7.1 in
Width: 13.6 cm/ 5.4 in
Depth: 25.3 cm/ 10.0 in
Pages: 5
Pieces: 60
Level: Medium-Hard
Designer: PODragon
Photo: LuIS
NOTES: Start at the face and build the fur around it. The head and the connections between the front legs and the head a can be a little tricky, so take your time there. Build the front legs from the paws up. The pieces of the spikes at the back need to be folded in order to get the right shape. Close the model at the rear paws and glue the tail. Finnish it by gluing the start at the tip of the tail.

Download: A4 / Letter

MEGA HOUNDOOM (Happy Halloween!)

229 / M Houndoom - Pokémon Papercraft
Name: M Houndoom
Type: Dark/Fire
Species:  Dark Pokémon
Height: 1.9 m (6'03")
Weight: 49.5 kg (109.1 lbs.)
Interesting Facts: As Mega Houndoom, the ridges on its back thicken, and it gains additional, bone-like rings around the base of its tail. The rings on its tail have small spikes on top, causing them to resemble vertebrae. The ridge at the base of Mega Houndoom's neck is longer and curves forward towards its shoulders. Instead of a band with a skull pendant, there is a large, toothed structure around its neck. This bone-like formation has two large spikes on either side and three pointed teeth on the bottom. Mega Houndoom's horns now point straight up with a small, outward curve in the middle. The two bands on its hind legs have vanished, and those on its forelegs are broken in the front. Its claws are a dark red due to its ability to generate more heat. Finally, the tip of its tail is now split down the middle.

THE PAPER MODEL
Height: 23.3 cm/9.2 in
Width: 11.3 cm/4.4 in
Depth: 20.5 cm/8.1 in
No. of Pages: 6
No. of Pieces: 87
Level: Hard
Designer: LuIS
Photo: LuIS

NOTES: Start at the mouth and glue the horns as you go. The next step is building the legs, build them from the paws up and glue the nails as you go. The leg bones may not need to be glued, place them and check if they stand. The hardest part of the model is building the bones. The neck one is by far the hardest. Start at the collar and build around it, join the bottom of it and close at the middle, by the back. Glue it only AFTER the bigger back bone is glued. You might have to apply some pressure to the neck collar, to give it the perfect shape. The back bones are hard to close only if you do it at the end, the trick is to build it by segments, I mean, close them while you're still building the top part. Join them to the body as soon as the numbers get to them. Make sure to glue the first piece of each of the rear legs BEFORE gluing the last back bone. I suggest placing the tail bones before building the legs. When you glue the tail doesn't matter, in fact, it may be even better to be glued at the end. Close the model at the rear paws and glue the nails after.

Download: A4 / Letter

CELEBI V2

251 / CELEBI (v2) - Pokémon Papercraft
Name: Celebi
Type: Psychic/Grass
Species: Time Travel Pokémon
Height: 0.6 m (2'00")
Weight: 5.0 kg (11.0 lbs.)
Interesting Facts: Celebi is a dual-type Psychic/Grass Legendary Pokémon. It is not known to evolve into or from any other Pokémon. It serves as the guardian of Ilex Forest and is only able to be caught from the wild in Pokémon Crystal with an event activated by the GS Ball. Celebi is the last Pokémon in the Johto Pokédex and Hoenn Pokédex, although in the latter, Celebi is not shown.

THE PAPER MODEL
Height: 22.0 cm/8.7 in
Width: 16.5 cm/6.5 in
Depth: 14.1 cm/5.6 in
No. of Pages: 4
No. of Pieces: 68
Level: Medium
Designer: LuIS
Photo: LuIS

NOTES: The model is divided into two main parts: head and body. Start the head at the face and close at the top. The body starts at the legs and it's closed at the top. Join both parts together by the spike, placing the glue inside the head. Glue the details (such as the antennaes and the wings) after the parts are joined. The antennaes can be kinda tricky to build, but if you get past the first 2 segments at the top, the rest gets easier. You can glue the antennaes before closing the head, to apply presure from the inside. You'll have to weight the model, just before closing the spike at the top of the body, sit the model on the base and put weight litlle by little inside the body and place the head to see when it stand. After it stands, close the body and glue the head to it. The base is simple, start at the top of the trunk and close at the bottom. If you choose to use the leaves and flowers, glue them after the base is built. You can also glue the model to the base.

Download: A4 / Letter

GOURGEIST

711 / GOURGEIST (Super) - Pokémon Papercraft
Name: Gourgeist
Type: Ghost/Grass
Species: Pumpkin Pokémon
Height: 1.7 m (5'07")
Weight: 39.0 kg (86.0 lbs.)
Interesting Facts: Gourgeist are malevolent Pokémon that catch their prey in their hairlike arms and take delight in their victims' suffering. On moonless nights, they are known to wander through town streets, singing an eerie song that curses its unfortunate listeners. It and its pre-evolution, Pumpkaboo, are the only known Pokémon that can learn Trick-or-Treat.

THE PAPER MODEL
Height: 19.9 cm/7.8 in
Width: 12.7 cm/5.0 in
Depth: 14.0 cm/5.5 in
No. of Pages: 5
No. of Pieces: 58
Level: Medium-Hard
Designer: Brandon
Photo: Brandon

NOTES: Start from the bottom up, closing the 'gourd' at the top, and doing the same with the arms. Build the arms from fingertip to top, being especially careful with connecting the fingers. Once the arms and bottom of the hair are done, connect them, being sure to hold the pieces together for a bit to get a strong connection. The next part is the trickiest, and most difficult- connecting the top of the hair onto the rest. Be sure to have something you can maneuver with like a scissor blade, pencil, or anything small and able to fit inside the piece. Use it to hold the tabs in place while gluing. Piece 56 is only advised if you're having trouble getting the hair to fit on the body.
Glue the hair by the back (pieces 49, 52, 53), being sure to position it to cover one eye and not the other. Will need a small wedge underneath the back to stand, or a little something to weigh it toward the front more.

Download: A4 / Letter

GLISCOR

472 / GLISCOR - Pokémon Papercraft
Name: Gliscor
Type: Ground/Flying
Species: Fang Scorpion Pokémon
Height: 2.0 m (6'07")
Weight: 42.5 kg (93.7 lbs.)
Interesting Facts: Gliscor is a large, mainly blue-purple vampire bat-like Pokémon. Its legs have two toes and a slightly darker circular coloration on the underside, and its tail has two barbs, giving its tail the resemblance of a vampire's fangs. Its arms are red with thin striations, and are completely detached from its black wings, and each are ended with large pincers. Its ears have discernible, red, chambered ear insides, and its eyes are yellow. It has six visible fangs in its mouth, and its waist, like its arms, is red and striated. Gliscor's body resembles an open mouth, with the pointed protrusions coming from its upper torso resembling fangs, further illustrating its vampiric qualities.

THE PAPER MODEL
Height: 17.0 cm/6.7 in
Width: 15.6 cm/6.1 in
Depth: 21.0 cm/8.3 in
No. of Pages: 7
No. of Pieces: 39
Level: Medium-Hard
Designer: Brandon
Photo: LuIS

NOTES: Start by building the head, which apart from the ears is quite easy. Build each piece separately but don't join them all together now, only at the end. The body is simple, just closing it can be a bit harder than usual. You need to reinforce the inside of the arms to hold the claws. Join the wing to the part between the head and torso. After that, glue the torso and the head. Be careful with the position you glue the torso, use the pdo as reference. You can either glue the claws now or proceed to the tail. If you follow the numbers and glue the tail, use the numbers on the pieces as reference. It takes a good time to glue, so if you can use superglue, it gets easier. To join the last segment, place the model on a flat surface, using the semi last segment as a reference and glue the last one keeping the flat surface. Also, make sure to leave the last two segments open, to insert weight and balance it, jut add weight until it stands after the arms are placed. The claws should be joined to the "wrist" before joining it to the arms. Must fold lines are included on the pdo. Note that the model, even after balanced, can fall with wind.

Download: A4 / Letter

AEGISLASH (Shield)

681 / AEGISLASH (Shield) - Pokémon Papercraft
Name: Aegislash
Type: Steel/Ghost
Species: Royal Sword Pokémon
Height: 1.7 m (5'07")
Weight: 53.0 kg (116.8 lbs.)
Interesting Facts: Aegislash's body is comprised of a golden sword with the blade pointing downwards. The edge of the blade is white and somewhat serrated near the tip. Its single eye, which is purple with a white, linear pupil, sits where the blade meets the hilt, where it is surrounded by black coloration. The handle is thick at its base, tapers as it progresses to the end, and is striated. Two cloth-like arms emerge from the sides of the hilt. Each arm is primarily black and ends in lavender, transitioned by a slight whorl between the two colors. It carries an ornate shield in at least one of its arms.

THE PAPER MODEL
Height: 23.9 cm/9.4 in
Width: 20.8 cm/8.2 in
Depth: 5.4 cm/2.1 in
No. of Pages: 4
No. of Pieces: 43
Level: Easy
Designer: Brandon
Photo: Olber

NOTES: Follow the numbers, starting from the bottom of the blade going up. When connecting the shield to the body, you can choose to either glue the arms directly to the shield and then glue on the handle, or put a magnet in the shield and handle to hold them (impermanently) together that way too. Close at the top. Weight the base if you wish to use it.

Download: A4 / Letter

BRAIXEN

654 / BRAIXEN - Pokémon Papercraft
Name: Braixen
Type: Fire
Species: Fox Pokémon
Height: 1.0 m (3'03")
Weight: 14.5 kg (32.0 lbs.)
Interesting Facts: Braixen is a bipedal, fox-like Pokémon. While the majority of its fur is yellow, it has black legs, white arms, face and neck, and a dark orange tail tip. The fur on its cheeks is longer, and a small mane of white fur covers its shoulders and chest. Long, wavy tufts of dark orange fur grow out of its large ears, and its eyes and small nose match this fur in color. Above its legs, the fur sweeps out to either side. When its mouth is open, two pointed teeth can be seen on its upper jaw. Braixen always keeps a stick in its tail, which it sets alight using its bushy tail fur. The flame from the lit twig is used for both attack and communication.

THE PAPER MODEL
Height: 17.8 cm/7.0 in
Width: 15.7 cm/6.2 in
Depth: 10.8 cm/3.6 in
No. of Pages: 4
No. of Pieces: 77
Level: Hard
Designer: Brandon
Photo: LuIS

NOTES: The model is composed of several parts: lower body, torso, arms, wand, and details of the body. The order you build is not important, but they must be assembled starting by joining the tail to the lower body, the torso to the lower body, arms to torso and the details and the wand at last. The lower body starts at the feet and it's built up. Be careful around the waist with all the spikes, it's one of the hardest parts of the model. I suggest folding the lines on these spikes, makes them easier to build. The tail is simple, start at the spikes at the bottom and close at the top, gluing the fur after it's built. Place the legs on a flat surface and glue the tail to it, using the pdo as reference. The torso starts at the head and it's built down. Closing it is the hardest part of the model, make sure to take your time there. It's necessary to reinforce the inside of the neck by gluing some pieces of scrap paper there, otherwise the head will fall. Also, there are optional teeth (not shown in the picture). The arms are simple, take your time at the fingers and you'll have no problem. The ear tufts can offer some trouble on the last piece if not folded on the spikes. Glue them to the head before gluing the wand. Proceed to gluing the details such as the spikes on the torso, close to the arms, the wand and the flame. I needed some weight, placed inside the tail for it to stand. Since all the pieces are separated, you have some choices regarding pose, such as the position of the arms and the rotation of the torso. The one shown in the picture is slightly different from the pdo one. If you use another pose that not the do's, be careful so the ear tuffs won't collapse with the flame and that it doesn't get too unstable.

Download: A4 / Letter

FLOETTE

670 / FLOETTE - Pokémon Papercraft
Name: Floette
Type: Fairy
Species: Single Bloom Pokémon
Height: 0.2 m (0'08")
Weight: 0.9 kg (2.0 lbs.)
Interesting Facts: Floette has white body and a green tail, shaped like a spade, and green eyebrows. Floette also appears to be holding a flower, which can be red, yellow, orange, blue, or white, depending on its pre-evolution's. Its ears are white with yellow behind them. It flutters around and cares for flowers that are about to wilt; if the flowers of a well-tended flower bed bloom, Floette celebrates with an elegant dance. It is a female-only species with no male counterpart.

THE PAPER MODEL
Height: 27.5 cm/10.8 in
Width: 38.1 cm/15.0 in
Depth: 23.4 cm/9.2 in
No. of Pages: 5 (AZ)/6 (Regular)
No. of Pieces: 15
Level: Medium
Designer: Brandon
Photo: Toshi
NOTES: Start at the face, and work your way through the body and close at the 'tail'. Build the flowers in the order indicated by the numbers. Put a couple pennies in the base to counter the weight of the flower.
Build whichever flower you'd like, but keep in mind AZ's Floette's body is purple, whereas normal Floette is green. The default is regular Floette with a Blue flower. Print only the flowers you intend to build.
Textures included for all 5 flowers.

Download: A4 / Letter

UMBREON HOWL

197 / UMBREON - Howl- Pokémon Papercraft
Name: Umbreon
Type: Dark
Species: Moonlight Pokémon
Height: 1.0 m (3' 3")
Weight: 27.0 kg (59.5 lbs)
Interesting Facts: When agitated, this Pokémon protects itself by spraying poisonous sweat from its pores. Also, on the night of a full moon, or when it gets excited, the ring patterns on its body glow yellow. It evolves from Eevee by Happiness during the night or when around a Moon Shard.

THE PAPER MODEL
Height: 16.5 cm/6.5 in
Width: 9.8 cm/3.9 in
Depth: 15.7 cm/6.2 in
No. of Pages: 4
No. of Pieces: 41
Level: Medium-Easy
Designer: PODragon
Photo: LuIS
NOTES: The model starts at the head and it's closed at the back legs. The ears and tail can be quite heavy, so reinforcing from the inside with scrap paper glued to the place where they connect is highly recommended. Start pieces 38 and 39 by the tabs with the *.

Download: A4 / Letter

UMBREON ATTACK

197 / UMBREON - Attack - Pokémon Papercraft
Name: Umbreon
Type: Dark
Species: Moonlight Pokémon
Height: 1.0 m (3' 3")
Weight: 27.0 kg (59.5 lbs)
Interesting Facts: When agitated, this Pokémon protects itself by spraying poisonous sweat from its pores. Also, on the night of a full moon, or when it gets excited, the ring patterns on its body glow yellow. It evolves from Eevee by Happiness during the night or when around a Moon Shard.

THE PAPER MODEL
Height: 16.5 cm/6.5 in
Width: 9.6 cm/3.8 in
Depth: 17.9 cm/7.1 in
No. of Pages: 4
No. of Pieces: 44
Level: Medium-Easy
Designer: PODragon
Photo: LuIS
NOTES: The model starts at the head and it's closed at the back legs. Some parts can be a bit complicated if you don't pay attention, such as piece 20, start this one by the place close to the * and stop gluing it when you reach the place where piece 23 (right leg) goes, glue the leg and proceed. The ears and tail can be quite heavy, so reinforcing from the inside with scrap paper glued to the place where they connect is highly recommended. The teeth are quite small, so tweezers are recommended, glue them as soon as the mouth is done.

Download: A4 / Letter

VIVILLON

666 / VIVILLON - Pokémon Papercraft
Name: Vivillon
Type: Bug/Flying
Species: Scale Pokémon
Height: 1.2 m (3'11")
Weight: 17.0 kg (37.5 lbs.)
Interesting Facts: Vivillon is a butterfly-like Pokémon with wings that come in a large variety of patterns. Vivillon's thorax is an elliptical shape divided into three segments, each with a different shade of gray. Its legs are also elliptical which are black on the lower half and grayish on the upper half. Vivillon has two black, circular hands and no visible arms. It has a round, grayish head with large, black, pixelated eyes and a pair of skinny antenna. It can spread its scales to calm an opponent's fighting spirit, as shown in the anime. Its wings' pattern is affected by the climate in which it lives.

THE PAPER MODEL
Height: 28.7 cm/11.3 in
Width: 32.0 cm/ 12.6 in
Depth: 5.0 cm/2.0 in
No. of Pages: 5
No. of Pieces: 15
Level: Medium/Hard
Designer: Brandon
Photo: LuIS
NOTES: Start at the head and proceed to the body, both pretty simple to build. After the head is built, build the arms, legs and antennae, they're all tricky so take your time and use tweezers for the tabs. The antennae can be hard, specially when joining the top and the tubes.
The wings are pretty simple, glue the back to the front using a little bit of glue and glue small segments at a time to avoid wrinkles. Be sure to cut the wings curvy too, not exactly on the sharp edges.
 Start joining at the parts together by gluing the head to the torso. After that the wings to the body (note that the wings must be curved in order to fit), use a good glue at this point and the pictures as a reference for the curvature and the place to glue. After the model is built, gluing the appendages to the body will be simple.

The textures for the wings can be changed (default is Meadow), but you'll need the pdo for that. Savannah form is pictured.

Download: A4 / Letter

DRAGONITE V2

149 / DRAGONITE V2 - Pokémon Papercraft
Name: Dragonite
Type: Dragon/Flying
Species: Dragon Pokémon
Height: 2.2 m (7'03")
Weight: 210.0 kg (463.0 lbs.)
Interesting Facts: Dragonite is a draconic, bipedal Pokémon with light orange skin. It has large, gray eyes and a round snout with small nostrils. There is a pair of long, thin antennae, as well as a small horn on the top of its head. Its striated underbelly is cream-colored, and extends to the tip of its long, tapering tail. It has thick arms and legs ending in three claws each. Its leg joints are well defined, while its arms have a smooth, rounded appearance. Dragonite's wings are small relative to its body, with teal wing membranes.

THE PAPER MODEL
Height: 14.0 cm/5.5 in
Width: 12.5 cm/4.9 in
Depth: 20.6 cm/8.1 in
No. of Pages: 4
No. of Pieces: 67
Level: Medium-Easy
Designer: PODragon
Photo: LuIS
NOTES: This model is pretty simple. Start at the head and build down. The antenaes can be tricky, just take you time and use tweezers. Close at the tip of the tail. Further instructions included on the template.

Download: A4 / Letter

MAROWAK

105 / MAROWAK - Pokémon Papercraft
Name: Marowak
Type: Ground
Species: Bone Keeper Pokémon
Height: 1.0 m (3'03")
Weight: 45.0 kg (99.2 lbs.)
Interesting Facts: Pokémon Red, Blue, Yellow, FireRed, and LeafGreen: Marowak was killed by agents of Team Rocket, leaving a Cubone as an orphan. With the Silph Scope, its ghost could be seen in Pokémon Tower. It can only be caught by using a cheating device. After fainting in a battle, a message will pop up saying that the Marowak's soul has finally moved on to the afterlife. This message, however, still shows up even if the player actually caught the Marowak with a Gameshark or Action Replay given that the Marowak is not supposed to be catch-able.

THE PAPER MODEL
Height: 18.0 cm/7.1 in
Width: 21.2 cm/ 8.3 in
Depth: 20.7 cm/8.1 in
No. of Pages: 5
No. of Pieces: 34
Level: Medium
Designer: PODragon
Photo: LuIS
NOTES: Build the model from the skull down, closing at the tail. Be careful with the hands. It's not necessary to glue the bone, but it's suggested using some magnets for a perfect placement, use inside the bone and the right hand. It can't stand on it's own, use some coins in the tail to make it stand.

Download: A4 / Letter

CUBONE V2

104 / CUBONE V2 - Pokémon Papercraft
Name: Cubone
Type: Ground
Species: Lonely Pokémon
Height: 0.4 m (1'04")
Weight: 6.5 kg (14.3 lbs.)
Interesting Facts: Cubone is a small, bipedal Pokémon with a golden brown hide that covers most of its body, including both dorsal spikes. Its belly is a very light brown. Two small claws, one on each hand, serve as its thumbs, and two large nails make up its toes. On its head, Cubone wears the skull of its dead mother as a helmet.

THE PAPER MODEL
Height: 17.0 cm/6.7 in
Width: 15.0 cm/ 5.9 in
Depth: 12.7 cm/5.0 in
No. of Pages: 4
No. of Pieces: 33
Level: Medium-Hard
Designer: PODragon
Photo: LuIS
NOTES: Start at the head and work down. Be careful at the skull, folding the lines is really important, specially with piece 12. The arms can be positioned at the builder's will, but be careful so the bone won't touch the head. Close the model at the tail. Further instructions on the template.

Download: A4 / Letter

LANDORUS (INCARNATE)

645 / LANDORUS (Incarnate Forme) - Pokémon Papercraft
Name: Landorus
Type: Ground/Flying
Species: Abundance Pokémon
Height: 1.5 m (4'11")
Weight: 68.0 kg (149.9 lbs.)
Interesting Facts: Landorus made his debut in Stopping the Rage of Legends! Part 1. He appeared in the legend of Milos Island related to Ash and his friends by Lewis, and later appeared at the end of the episode when called to stop the battle of Tornadus and Thundurus. He then appeared in Stopping the Rage of Legends! Part 2, where he managed to subdue the other members of the Forces of Nature. He hasn't however, managed to subdue the Landorus-EX hype.

THE PAPER MODEL
Height: 22.7 cm/8.9 in
Width: 25.8 cm/ 10.2 in
Depth: 24.3 cm/9.6 in
No. of Pages: 9
No. of Pieces: 90
Level: Hard
Designer: Brandon
Photo: Olber
NOTES: Build from top to bottom. Do the Cloudy- Hair first. Then go your way down. Be patient with fingers. Build the Cloud base from bottom to top. Stick the tail when you're done.  No need to print the last page (or first page, as usual). Additional notes on template.

Download: A4 / Letter

PROFESSOR OAK

PROF OAK - Pokémon Papercraft
Name: Professor Samuel Oak
Species: Professor
Appearance: Pokémon Red/Blue, Origins
Interesting Facts: Professor Oak works in his Laboratory in Pallet Town with his aides. He gave Red and Blue their Starter Pokémon in Pokémon Red, Blue, Green, Yellow, FireRed and LeafGreen. He is an idol to many Trainers and researchers, including Professor Elm, and always plays an important supporting role in the many games that he appears in.

THE PAPER MODEL
Height: 23.5 cm/ 9.3 in
Width: 9.4 cm/ 3.7 in
Depth: 7.4 cm/ 2.9 in
Pages: 6
Pieces: 74 
Level: Medium-Hard
Designer: Brandon
Photo: LuIS
NOTES: Start the model by the head. Glue the first piece of the torso around it and continue building the torso with the head connected. Proceed to the jaket, you can fold the pockets a bit to give them some depth, but don't connect it now, wait until the end to do so. After that, build the legs. The belt is simple, just build the buckle taking care to fold it on the indicated lines and pass the belt by the space. Do it before gluing the jacket. The hands are the hardest part, take your time there and follow the numbers. Make sure to glue the sleves before gluing the hands. The collars should be glued before joining the jacket. Glue them by the edges. The jacket should be joined before the feet, which are the last part of the model. There's no actual need to glue the jacket, after the hands are connected they kinda lock it in place. Glue the feet and the slippers together before gluing them to the body. Close the slippers at the bottom. The Pokedex should stand still.

Download: Download

TORNADUS (INCARNATE)

641 / TORNADUS (Incarnate Forme) - Pokémon Papercraft
Name: Tornadus
Type: Flying
Species: Cyclone Pokémon
Height: 1.5 m (4'11")
Weight: 63.0 kg (138.9 lbs.)
Interesting Facts: In Incarnate Forme, Tornadus is a green, muscular humanoid Pokémon, which resembles a genie. It is a male-only species with no female counterpart. On its forehead are two, purple, long and sharp horns. Tornadus has white, wavy and billowy styled hair, a spiky white mustache and two pointed green ears on either side of its head. Its eyes are yellow with beady white irises and no visible pupils.

THE PAPER MODEL
Height: 26.0 cm/10.2 in
Width: 22.2 cm/ 8.7 in
Depth: 27.9 cm/11.0 in
No. of Pages: 11
No. of Pieces: 88
Level: Hard
Designer: Brandon
Photo: Olber
NOTES: Build from top to bottom. Do the Cloudy- Hair first. Then go your way down. Be patient with fingers. Build the Cloud base from bottom to top. Stick the tail when you're done.

Download: A4 / Letter

THUNDURUS (INCARNATE)

642 / THUNDURUS (Incarnate Forme) - Pokémon Papercraft
Name: Thundurus
Type: Electric/Flying
Species: Bolt Strike Pokémon
Height: 1.5 m (4'11")
Weight: 65.0 kg (143.3 lbs.)
Interesting Facts: In Incarnate Forme, Thundurus is a blue, muscular humanoid Pokémon, which resembles a genie. It is a male-only species with no female counterpart. On its head is a single, long, sharp, purple horn. Thundurus has white, zigzagging and jutting styled hair, a spiky white mustache and two pointed blue ears on either side of its head. Its eyes are yellow with beady white irises and no visible pupils.

THE PAPER MODEL
Height: 25.7 cm/10.1 in
Width: 24.2 cm/ 9.5 in
Depth: 29.5 cm/11.6 in
No. of Pages: 11
No. of Pieces: 99
Level: Hard
Designer: Brandon
Photo: Olber
NOTES: Build from top to bottom. Do the Cloudy- Hair first. Then go your way down. Be patient with fingers. Build the Cloud base from bottom to top. Stick the tail when you're done.

Download: A4 / Letter

PELIPPER

279 / PELIPPER - Pokémon Papercraft
Name: Pelipper
Type: Water/Flying
Species: Water Bird Pokémon
Height: 1.2 m (3'11")
Weight: 28.0 kg (61.7 lbs.)
Interesting Facts: Pelipper is a pelican-like Pokémon with no discernible neck. Its head and bill make up the majority of its body. It has white feathers, a yellow underbelly, and a blue head crest. Its large wings have three digits and blue wing tips. It has small, blue webbed feet, a short tail, and eyes that are made of two black semi-circles. It has a large bill and a throat pouch that it uses to carry small Pokémon and eggs and scoop food from the sea. It searches for food by skimming across the wave tops. After scooping the food, Pelipper swallows it in one big gulp. It builds its nest on steep cliffs facing the sea.

THE PAPER MODEL
Height: 14.2 cm/5.6 in
Width: 19.6 cm/ 7.7 in
Depth: 22.9 cm/9.0 in
No. of Pages: 7
No. of Pieces: 34
Level: Easy/Medium
Designer: Brandon
Photo: LuIS
NOTES: Start at the top of the head and close at the tip of the tail. Be sure to build the entire mouth before gluing it to the face. The wings are the only hard part, but as long as you fold the lines indicated in red it will build fairly simply. When gluing the feet, place the left wing on a flat surface and glue the feet on the same level so it stands better. You can use magnets to hold the bill instead of gluing it (to make it into a storage container of sorts), just place one inside the bill before closing and glue one to the place where it connects to the body.

Download: A4 / Letter

EXPLOUD

295 / EXPLOUD - Pokémon Papercraft
Name: Exploud
Type: Normal
Species: Loud Noise Pokémon
Height: 1.5 m (4'11")
Weight: 84.0 kg (185.2 lbs.)
Interesting Facts: Exploud is a large blue bipedal Pokémon with a large mouth. It has two peg-like teeth on each jaw. It has protruding tubes with holes along its body: seven along the crest on its head, four on its elbows and knees, two along its back, and two on the end of its two tails. Exploud's bellowing is capable of triggering earthquakes and can be heard from over six miles away. It only raises its voice when it is in battle. It communicates its feelings to others by producing whistle-like sounds. It lives in caves.

THE PAPER MODEL
Height: 16.5 cm/6.5 in
Width: 15.7 cm/ 6.2 in
Depth: 17.6 cm/6.9 in
No. of Pages: 5
No. of Pieces: 42
Level: Medium
Designer: PMF
Photo: LuIS
NOTES: Start at the top of the head, build the tubes first and the face around them. The mouth is glued after the first piece of the back is glued. Glue pieces 17 and 20 to the arms after the first segments of pieces 16 and 19 are built. The parts under the mouth (22 and 23) can get tricky, start them at the bottom of the lips. Close at the tip of the tails.

Download: A4 / Letter

TOGEKISS (Happy Easter!)

468 / TOGEKISS - Pokémon Papercraft
Name: Togekiss
Type: Fairy/Flying
Species: Jubilee Pokémon
Height: 1.5 m (4'11")
Weight: 38.0 kg (83.8 lbs.)
Interesting Facts: Togekiss is a white, avian Pokémon with an ovoid body. While its feet are small and situated closely together, its wings are broad and triangular. Red and blue triangular markings over its underside, and it has a short tail consisting of three feathers. On the back of its head are three spikes: a red tipped on the right, a blue tipped one on the left, and a pure white one in the middle. Togekiss has a relatively flat face and small, black eyes. This Pokémon is rarely seen, only appearing in peaceful areas. When it is seen or visits respectful people, it showers gifts of blessings and kindness.

THE PAPER MODEL
Height: 16.5 cm/6.5 in
Width: 29.9 cm/11.8 in
Depth: 19.7 cm/7.8 in
No. of Pages: 7
No. of Pieces: 75
Level: Medium
Designer: Brandon
Photo: LuIS
NOTES: Start the model at the top of the head, follow the numbers and the istructions and close at the tail. The only part that can offer some trouble on this one is joining the wings with the body, since they are quite big. If you glue the two first chest pieces to it, will make it easier. It stands on it's own, just be careful while placing the feet so they match the pdo and the picture. If it won't stand, add some weight, there should be an opening, since the tail should be only glued after it's standing. To finish it, glue the feathers.

About the wings, up until a point (12), the build with both the wings is the same, after that, if you want the wings as shown on the picture, follow the red numbers, if you want the ones as shown on the pdo, use the black numbers.

Download: A4 / Letter

STARLY

396 / STARLY- Pokémon Papercraft
Name: Starly
Type: Normal/Flying
Species: Starling Pokémon
Height: 0.3 m (1'00")
Weight: 2.0 kg (4.4 lbs.)
Interesting Facts: Although capable of flapping its wings powerfully, Starly is weak and inconspicuous when alone. It forms large flocks to protect itself. However, individuals will begin to bicker if the group becomes too large. This Pokémon’s cry is harsh, and its singing can become annoying. Starly congregates in mountains and fields, where it hunts for bug Pokémon.

THE PAPER MODEL
Height: 16.8 cm/ 6.6 in
Width: 16.9 cm/ 6.7 in
Depth: 30.2 cm/ 11.9 in
No. of Pages: 5
No. of Pieces: 40
Level: Medium
Designer: LuIS
Photo: LuIS
NOTES: The model is built in two main parts: head and body. Start the head at the top feather and work down, it's pretty simple. The body starts at the tail. Remember do glue the legs and wings to it BEFORE closing. The legs are simple, just start at the toes and work by numbers. The wings are built in segments, the instructions on the templates explain how they are supposed to be built. The model might need some weight to stand. Before closing the body, put some weight inside and pop the head until it stands, when it does, close the body and glue the head to it.
Both the textures for Male and Female variants are included, with the Male textures used for non-shiny PDFs and the Female textures used for shiny PDFs.

Download: A4 / Letter

STARAPTOR

398 / STARAPTOR - Pokémon Papercraft
Name: Staraptor
Type: Normal/Flying
Species: Predator Pokémon
Height: 1.2 m (3'11")
Weight: 24.9 kg (54.9 lbs.)
Interesting Facts: Staraptor is a grayish-brown, avian Pokémon similar to a large bird of prey. It has small, red eyes and a thin, yellow beak with a black tip. There is a circular white patch on its forehead, which is smaller on the female. Larger white markings cover the front of its throat and chest, separated by a black ruff encircling the shoulders. A red-tipped, black crest extends over its head, nearly reaching the tip of its beak.

THE PAPER MODEL
Height: 20.6 cm/8.1 in
Width: 18.5 cm/7.3 in
Depth: 30.2 cm/11.9 in
No. of Pages: 6
No. of Pieces: 56
Level: Hard
Designer: LuIS and Brandon
Photo: LuIS
NOTES: The model is built in two main parts: head and body. Start the head at the top feather and work down. The body starts at the tail, which is pretty hard to build. Fold the indicated lines and take your time there. Remember do glue the legs and wings to the body BEFORE closing. Start the legs at the claws and work by numbers, reinforce them from the inside, the model is pretty heavy. The wings are built in segments, the instructions on the templates explain how they are supposed to be built. The model needs weight to stand. I create a pocked inside the body to counterbalance it, reference pictures and instructions are added on the pack and on the template. Add the weight inside and pop the head until it stands, when it does, close the body and glue the head to it. Further instructions added on the template.

Download: A4 / Letter

April Fool's Chinpokomon Papercrafts

April Fool's Chinpokomon Papercraft
Sorry, this year there was no models for April Fool's Day. For those who don't know Chinpokomon, they are from an episode of South Park (S3E11) which was a parody of the Pokémon. And well, you can't really make a model if you don't really know what they look like... I mean, look at the pic with the kids up there, you can't really make a model out of that.  :/

So there you go, sorry to those who don't really know what April Fool's all about, or just got caught thinking we were hacked or changed name. :) Always funny to read your comments tho. hahaha

The download links were the Chinpokomon ad from the episode and the Google Maps Pokémon challenge trailer, which was pretty great! : A4 / Letter
We'll be back to our regularly scheduled models by Friday.

DODRIO

085 / DODRIO - Pokémon Papercraft
Name: Dodrio
Type: Normal/Flying
Species: Triple Bird Pokémon
Height: 1.8 m (5'11")
Weight: 85.2 kg (187.8 lbs.)
Interesting Facts: Along with its three heads, Dodrio has three sets of hearts and lungs as well. This allows it to efficiently oxygenate and pump blood throughout its body, thus giving it increased endurance to run vast distances without rest. It is especially prone to race vigorously across grassy plains, even in arid seasons with little rainfall.

THE PAPER MODEL
Height: 22.0 cm/8.7 in
Width: 15.1 cm/ 5.9 in
Depth: 14.1 cm/5.6 in
No. of Pages: 3
No. of Pieces: 76
Level: Medium-Hard
Designer: Brandon
Photo: LuIS
NOTES: There are two start points: the heads and the legs. After both segments are done, join them with the indicated piece. The beaks can offer some trouble, take your time there. For a smoother build it's suggested to fold the indicated lines. After the model is closed, glue the tail. The head details can be glued after the heads are connected to the torso. The necks and the legs might break with time, some reinforcement is suggested, such as a thin wire on the necks and a thicker one for the legs or some stripes of paper inserted in them. The model won't stand on it's own, in order to do that you can use a base.

There are also textures included for both the apricot colored neck (female) and darker neck (male). The default is female, Pepakura Viewer is needed to use the male textures.

Download: A4 / Letter

MEGA BLAZIKEN

257 / M-BLAZIKEN - Pokémon Papercraft
Name: Mega Blaziken
Type: Fire/Fighting
Species: Blaze Pokémon
Height: 1.905 m (6'03")
Weight: 52.1 kg (114.6 lbs.)
Interesting Facts: As Mega Blaziken, it loses its yellow markings, and gains black markings on its upper legs and chest. Its hair like feathers take on a wing-like shape and point upward, and the portion around its chest is rough around its shoulders. The crest on its head changes into a flat horn that curves backward. The fire it creates on its wrists is now longer, as well.

THE PAPER MODEL
Height: 19.8 cm/7.8 in
Width: 15.8 cm/ 6.2 in
Depth: 11.1 cm/4.4 in
No. of Pages: 3
No. of Pieces: 74
Level: Medium-Hard
Designer: Brandon
Photo: LuIS
NOTES: The model starts at the belly and at the hair. Start at the legs, but close only the standing one now. Make sure to follow the instructions of when to glue each detail, specialy at the top with the arms and some fur. Close the torso at the bottom of it and glue to the legs. Make sure to reinforce the standing leg with some scrap paper glued into it. The model will need some weight to stand, so keep one leg open and only AFTER the ENTIRE model is glued together, put weight inside so it stands properly, close the leg after it's balanced and glue the details to it. There's a base with it, it should prevent the leg fur from beeing damaged from the weight. Numbers and further instructions included on the template.

Download: A4 / Letter

BLAZIKEN V2

257 / BLAZIKEN - Pokémon Papercraft
Name: Blaziken
Type: Fire/Fighting
Species: Blaze Pokémon
Height: 1.905 m (6'03")
Weight: 52.1 kg (114.6 lbs.)
Interesting Facts: Blaziken was first seen in Pop Goes The Sneasel. Harrison used it to defeat the Sneasel that was blocking access to the flame of Ho-Oh. Harrison later used Blaziken in a climactic battle with Ash's Charizard.

THE PAPER MODEL
Height: 19.8 cm/7.8 in
Width: 19.3 cm/ 7.6 in
Depth: 11.8 cm/4.6 in
No. of Pages: 4
No. of Pieces: 76
Level: Hard
Designer: Brandon
Photo: LuIS
NOTES: The model had two start points, both being at the torso. Start by the legs, only don't close that part just yet. The torso is where parts can get complicated, the fur and the hair being the hardest parts of the model. There are plenty of notes and colored references on the template, I suggest using them all. The model can't stand on it's own, so weight is necessary, put it inside, BEFORE closing the legs and only AFTER the ENTIRE model is glued together, close the leg after it's balanced and glue the details to it. Also note that the standing leg MUST be reinforced from the inside, do so by gluing pieces of scrap paper into it. There's a base with it, it should prevent the leg fur from being damaged from the weight. Numbers and further instructions included on the template.

Download: A4 / Letter